防爆电动葫芦是按最新防爆标准设计制造的防爆起重设备，其防爆形式为“隔爆型”，防爆电动葫芦的外露防爆零部件采用特殊的无火花材料制成。

Explosion-proof electric hoist is according to the latest explosion protection standard design and manufacture of lifting equipment, its explosion proof form for the flameproof, explosion-proof electric hoist explosion-proof exposed parts adopt no spark of special materials.

　　防爆电动葫芦吊物时的起车和运行方法不当，会使吊物摆动发生事故。吊物运行时，由起重操作人员在电动葫芦吊物后面扶稳物件，并在起重工指挥下绕过障碍运行。重物开始起升时，当钢丝绳或链条拉紧时应停车，电动葫芦按吊钩抖动的方向再次找准吊钩，同时起重工人应检查吊物是否挂牢；起升不要过猛，当吊物脱离障碍以后方可加快起升速度；防爆电动葫芦运行时不要时断时续，在长距离运行时，最好以长时间送电运行为好，在运行时应保证吊物平稳，不得任其抖或摆。

Explosion-proof electric hoist crane when a car and run method is undeserved, can make the crane swing accident. "Operation, the lifting operators to balance from behind electric hoist crane, and under the rigger command to bypass obstacles. Weight started lifting, should stop when wire rope or chain taut, electric hoist by direction again for hook, hook shaking at the same time lifting workers should check whether "hang up; Hoisting don't too hard, when hanging out after barriers can speed up the lifting; Explosion-proof electric hoist run-time don't starts, in the long run, the best run either for a long time, for good, smooth should guarantee the hanging objects at runtime, not allow it to shake or place.

　　防爆电动葫芦磨机部位滑线故障时有发生，给人们在使用过程中带来了很多不便。下面简单说一下防爆电动葫芦滑线的安装方法。

Explosion-proof electric hoist the malfunction is always occurring about the slide wire mill parts, give people brought a lot of inconvenience in use process. The following simple said the explosion-proof electric hoist slide wire installation method.

　　1、防爆电动葫芦多安装在轨道上，把钢索布置在轨道中间，工字钢上部，端部用花篮螺栓紧固。

More than 1, explosion-proof electric hoist installation on the orbit, decorate the wire in the middle of the track, beams, end with a flower basket bolts.

　　2、滑动环为两圆环相扣，有一定余量，以避免钢索刮卡。

2, sliding ring for two ring clasp, have certain allowance, in order to avoid wire scratch CARDS.

　　3、在电动机的牵引下，以转向环为中心，牵引钢索作直线或圆周运动。

3, under the traction of the electric motor to turn ring as the center, traction rope make linear or circular motion.

　　4、把一个转向环一端套在钢索上，留好电动机引线后把橡套线固定在转向环下端。前端接电动机，可自由移动。后端接在电源上。

4, turned to a ring set on the wire at one end and leave a good motor lead after the rubber sleeve fixed in turn ring bottom line. The front motor, can move freely. After the termination on the power supply.

　　以上方法简便易行，可以消除以往防爆电动葫芦滑线因接触不良、引线短路、断路而引起的一些问题。

The above method is simple and easy, can eliminate the explosion-proof electric hoist, lead by bad contacts of slide wire short circuit, open circuit and cause some problems.